Need some bamboo builder/restorer input

Russell

Life of the Party
Forum Supporter
I have a w&M granger 8642 that has a ferrule that is loose. Can click it up and down by hand. The rod is worth having it done with the right thread wraps as a restoration but I am not interested in paying for all the shipping but maybe it is just worth doing.
Any input is appreciated. The section seems to still want to hold on to this ferrule. Read that it may be crimped. Suggestions to get it off the rod, epoxy, and such would be good to know. If it is hard to get off I am assuming it is hard to get back on.. Do I need to widen the ferrule?
Even after typing this I am feeling like my best bet is to send it to someone. Any suggestions?
Still though I feel I can do this and let someone else get the thread right later if they want.

Russell
 
Hi Russell, can you post a close up picture of the ferrule? Check to see if there’s a small metal pin holding it on. If it moves up and down much, maybe not pinned. To remove the ferrule, use a lighter and slowly add carefully heat and pull straight. Don’t twist. Also mark the ferrule and rod to reinstall it in the same place. I use five minute epoxy or clear Gorilla glue.
Too bad you live so far, I’d be glad to help!
 
Without taking pictures all around the ferrule, you don’t see a small round metal pin, correct? The trim wrap is only on the blank, right? When you move the ferrule, can you see it separate from the wrap? Try heating it a bit and see if it moves more…..be careful not to put much heat on the wrap.
 
The 8642 is a really nice taper and rod, a great 5wt. I have several of them and have fished them a lot.
It’s worth fixing it right and getting it back out on the water. I don’t know what happened to Chris Raine, but he was a bamboo rod maker that could possibly have done the repair. I thought of him because he used to have his shop nearish you in Dunsmuir, but I think it’s closed up now.
Dennis Stone up near Portland can do it for you. Shipping it really is not a big deal but package it well if you do.
Granger ferrules are not pinned. The dimples that look like they might be pins on the male and female ferrules are called “witness” marks. They are meant to allow you to align the rod properly while assembling it.

What grade is marked on the rod? They made a bunch… Victory, Champion Deluxe etc.
 
The 8642 is a really nice taper and rod, a great 5wt. I have several of them and have fished them a lot.
It’s worth fixing it right and getting it back out on the water. I don’t know what happened to Chris Raine, but he was a bamboo rod maker that could possibly have done the repair. I thought of him because he used to have his shop nearish you in Dunsmuir, but I think it’s closed up now.
Dennis Stone up near Portland can do it for you. Shipping it really is not a big deal but package it well if you do.
Granger ferrules are not pinned. The dimples that look like they might be pins on the male and female ferrules are called “witness” marks. They are meant to allow you to align the rod properly while assembling it.

What grade is marked on the rod? They made a bunch… Victory, Champion Deluxe etc.
It is a deluxe and is in fantastic condition. The fix for the rod is to re glue the ferrule and this can be done to restore original rod or just to fix the problem and later to be restored with the proper matching thread. I'm just looking to fish it.
 
As already said, the Deluxe is a higher grade model and much sought after. And although not as pricey as a rod 7-8', the 8642, especially from the earlier Goodwin era, is a really wonderful, slower taper. One of the tricky things on that grade is to replace a single or a few wraps and somehow match the 90 year old wraps with their aged yellowed varnish. The thread is silk in a black and white jasper style. But the last thing you want is to have a single or a few bright white and black wraps juxtaposed to the original wraps that have that wonderful deep dark golden almost olive hue. The trick is to apply the right amount of aging toners to those wraps when finishing them with the new varnish. That's a good reason to find a restorationist who knows how to pull that off. And an early Goodwin Granger Deluxe is worth it IMO. Good luck on this!
 
Per @Mike Monsos that might be your best bet.
I just checked Rick Robbin’s website and it’s still active so you might reach out to him. He’s located in Lexington VA, about 4 hours from Asheville. He was good friends with Tom Maxwell so he would be a good source.
Nice Classic rod; it’s worth having it done right. Let us know how you make out. Merry Christmas 🎁
 
If you end up considering shipping it out for the repair you might want to contact Michael Clark in Colorado. He specializes in Grangers and has been building bamboo rods since 1979. He probably has the most extensive collection of Granger “Registerds” in existence.

He rebuilt a tip section of an 8642 “Favorite” for me a few years ago and it’s flawless. He’s in demand so might take awhile to fit you in, but it will be done right.

Here’s the link;
 
I have a w&M granger 8642 that has a ferrule that is loose. Can click it up and down by hand. The rod is worth having it done with the right thread wraps as a restoration but I am not interested in paying for all the shipping but maybe it is just worth doing.
Any input is appreciated. The section seems to still want to hold on to this ferrule. Read that it may be crimped. Suggestions to get it off the rod, epoxy, and such would be good to know. If it is hard to get off I am assuming it is hard to get back on.. Do I need to widen the ferrule?
Even after typing this I am feeling like my best bet is to send it to someone. Any suggestions?
Still though I feel I can do this and let someone else get the thread right later if they want.

Russell
A ton of options up here, like Mike Monsos, he makes his own ferrules. However finding someone with access to the exact OEM ferrules or someone who can repair the existing one is key!

Replacing would be a relatively easy process, but you would probably lose a little value of the rod. If that's even something you want to or need to factor in!

Matching the thread is a bit of a challenge, but anyone who does repair may have the correct silk thread. I personally have a bunch of old silk thread from my former mentor Aaron Reimer. Most threads didn't use color preserver, or I mean, most builders. It really depends on how old the rod is.

Cheers!
 
Back
Top